Integrated multimotor electrical dc drive for metallurgical rolling table

Czasopismo : Acta Mechanica et Automatica
Tytuł artykułu : Integrated multimotor electrical dc drive for metallurgical rolling table

Autorzy :
Chand, R.
Department of Mathematics, Government Arya Degree College Nurpur, Himachal Pradesh, 176202, India, rameshnahan@yahoo.com,
Rana, G. C.
Department of Mathematics, Government College Nadaun, Himachal Pradesh, 177103, India, drgcrana15@gmail.com,
Doroszko, M.
Faculty of Mechanical Engineering, Department of Mechanics and Applied Computer Science, Bialystok University of Technology, ul. Wiejska 45C, 15-351 Białystok, Poland, m.doroszko@doktoranci.pb.edu.pl,
Seweryn, A.
Faculty of Mechanical Engineering, Department of Mechanics and Applied Computer Science, Bialystok University of Technology, ul. Wiejska 45C, 15-351 Białystok, Poland, a.seweryn@pb.edu.pl,
Brestovič, T.
Faculty of Mechanical Engineering, Technical University in Kosice, Department of Power Engineering, Vysokoškolská 4, 042 00 Košice, Slovak Republic, tomas.brestovic@tuke.sk,
Jasminská, N.
Faculty of Mechanical Engineering, Technical University in Kosice, Department of Power Engineering, Vysokoškolská 4, 042 00 Košice, Slovak Republic, natalia.jasminska@tuke.sk,
Lázár, M.
Faculty of Mechanical Engineering, Technical University in Kosice, Department of Power Engineering, Vysokoškolská 4, 042 00 Košice, Slovak Republic, marian.lazar@tuke.sk,
Nosko, O.
Department of Machine Design, KTH Royal Institute of Technology, Brinellvägen 83, Stockholm 100 44, Sweden, nosko@dr.com,
Nagamine, T.
Department of Mechanical Engineering, Saitama University, 255 Shimookubo, Sakura Ward, Saitama City 338 8570, Japan, nagamine@mech.saitama-u.ac.jp,
Mori, H.
Department of Mechanical Engineering, Kyushu University, 744 Motooka, Nishi Ward, Fukuoka City 819 0395, Japan, hiroki@mech.kyushu-u.ac.jp,
Sato, Y.
Department of Mechanical Engineering, Saitama University, 255 Shimookubo, Sakura Ward, Saitama City 338 8570, Japan, ysato@mail.saitama-u.ac.jp,
Sapiński, B.
Department of Process Control, AGH-University of Science and Technology, Al. Adama Mickiewicza 30, 30-059 Kraków, Poland, deep@agh.edu.pl,
Gała, M.
Faculty of Electrical Engineering, Czestochowa University of Technology, Al. Armii Krajowej 17, 42-200 Częstochowa, Poland, mgala@el.pcz.czest.pl,
Jąderko, A.
Faculty of Electrical Engineering, Czestochowa University of Technology, Al. Armii Krajowej 17, 42-200 Częstochowa, Poland, aj@el.pcz.czest.pl,
Rak, J.
Faculty of Electrical Engineering, Czestochowa University of Technology, Al. Armii Krajowej 17, 42-200 Częstochowa, Poland, jrak@el.pcz.czest.pl,
Jagiełła, K.
Faculty of Management, Czestochowa University of Technology, Al. Armii Krajowej 17, 42-200 Częstochowa, Poland, kazimierz.jagiela@gmail.com,
Abstrakty : A drive system of a section of a metallurgical rolling table consisting of six dc motors, 2220 amperes of total current, fed from a single ABB reversible thyristor converter has been described in this paper. Autonomous excitation circuits of the motors are fed from independent thyristor converters working in the so called MULTIFEX system linked with a supervisory high power converter. There are presented schemes of the DSL communication realized by FEX excitation cards of the motors using the SDSC card of the DCS-800-S02 converter and logic control system based on a PLC controller. The parameterization of the DCS-800 converter and the DCF 803 excitation systems was conducted using the DriveWindow software tool. Significant waveforms of voltages, currents and the estimated motor velocity are described and presented for the idle run as well as during transporting sheets discharged from a pusher furnace.

Słowa kluczowe : system napędowy, DSL, sterowniki PLC, FEX excitation system, DC drive system, rolling table, DriveWindow software,
Wydawnictwo : Oficyna Wydawnicza Politechniki Białostockiej
Rocznik : 2015
Numer : Vol. 9, no. 2
Strony : 93 – 98
Bibliografia : 1. Abu-Rub H., Guziński J., Jąderko A., Krzemiński Z. (2004), Practical Realisation of New Method of Synchronisation for Controlled Rectifier, International Conference on Power Electronics, Intelligent Motions and Power Quality PCIM 2004, Nuremberg, Germany, 533 – 538.
2. Abu-Rub H., Guziński J., Jąderko A., Krzemiński Z. (2005), Digital Implementation of a Novel Controlled Rectifier Synchronization Method, Electric Power Components and Systems, Vol. 33 (10), 1123 – 1135.
3. Dobrucki W., Gregorczyk R., Świątoniowski A., Zawada S. (1991), Introduction to design and operation of rolling mills – Calculations and experiments, Wydawnictwo AGH, Kraków, (in Polish).
4. Friedli T., Hartmann M., Kolar J.W. (2014), The Essence of ThreePhase PFC Rectifier Systems—Part II, IEEE Transactions on Power Electronics, Volume: 29 (2), 543- 560.
5. Gała M., Rak J., Kępiński M., Jagieła K. (2009), Application of Drive Window software for AC and DC drives operation states diagnostics, Electric Machines – Problem Issues, No.82/2009, BOBRME KOMEL Katowice, 33-38, ISSN 0239-3646, (in Polish).
6. Guziński J., Diaguet M., Krzemiński Z., Lewicki A., Abu-Rub H. (2009), Application of speed and load torque observers in high-speed train drive for diagnostic purposes, IEEE Transactions on Industrial Electronics, Vol 57(2), 565-574.
7. Jagieła K. (1997), Theoretical issues in calculation of load parameters of rolling table motors. Research Notes of Lvov State University of Technology – Electrical power engineering and electro-mechanical systems Systemy, № 340, 142-147, (in Ukrainian).
8. Jagieła K. (2003), Model of metallurgical discharge rolling table, Electrical Review, No.6/2003, 448- 452.
9. Jagieła K., Gała M. (2008), Setting screw electrical drive of the vertical milling cage using MASTER– FOLLOWER control, IX Inter-national Scientific Conference „New Technologies in Metallurgy and Materials Engineering”, Metallurgy Committee PAS, Czestochowa University of Technology, Vol. 1, 146-149 (in Polish).
10. Kolar J. W., Friedli T. (2013), The Essence of Three-Phase PFC Rectifier Systems—Part I, IEEE Transactions on Power Electronics, Volume: 28 (1), 176-198.
11. Michael C.A., Safacas A.N. (2007), Dynamic and Vibration Analysis of a Multimotor DC Drive System With Elastic Shafts Driving a Tissue Paper Machine, IEEE Transactions on Industrial Electronics, Vol. 54 (4), 2033-2046.
12. Multifex motor control for roller tables DCS800 Drives (20 to 5200 A), ABB Automation Products, Germany, 05-2008.
DOI :
Cytuj : Chand, R. ,Rana, G. C. ,Doroszko, M. ,Seweryn, A. ,Brestovič, T. ,Jasminská, N. ,Lázár, M. ,Nosko, O. ,Nagamine, T. ,Mori, H. ,Sato, Y. ,Sapiński, B. ,Gała, M. ,Jąderko, A. ,Rak, J. ,Jagiełła, K. , Integrated multimotor electrical dc drive for metallurgical rolling table. Acta Mechanica et Automatica Vol. 9, no. 2/2015
facebook